- #CHIRP PROGRAMMING SOFTWARE FOR RADIOS HOW TO#
- #CHIRP PROGRAMMING SOFTWARE FOR RADIOS DRIVERS#
- #CHIRP PROGRAMMING SOFTWARE FOR RADIOS PC#
- #CHIRP PROGRAMMING SOFTWARE FOR RADIOS PLUS#
- #CHIRP PROGRAMMING SOFTWARE FOR RADIOS DOWNLOAD#
Enter the repeater output frequency, such as 147060.If you enter a frequency and the radio says “Cancel” when you press the last digit, press the “Band” button to select the correct band. Remember, channel mode will speak the channel number if you press the “up” or “down” button. If you are in channel mode, press the channel/frequency button.This is probably already done, but if you go through all the steps to program and get a single beep upon the final press of “Menu”, you are in the B VFO and need to press the “A/B” button. Choose the “A” frequency, printed on the top line of the display.Programming a repeater channel with standard offsets: Note that this trick to temporarily change power levels only works if TDR (dual watch, Menu 7, discussed earlier) is set to “Off”. The power level will revert to its stored value if you switch channels, press “Lock” again, or turn the radio off and then on again. the one not stored in memory, by pressing the “Lock” key (the # key on the keypad) while in memory mode. Power level can be temporarily set to its other value, i.e. Memories store receive and transmit frequencies, along with receive and transmit CTCSS or DCS codes, power level, and channel width (wide or narrow). Remember that once a memory is programmed, it cannot be changed, short of deleting it and starting over. You can program memories either with a standard split or with odd splits. See the menu section below for a more complete discussion of setting menu parameters. For frequencies in a 2.5 KHz channel spacing, such as 154.5275 set the radio to 154.525 and, with a 2.5 KHz channel spacing (Menu 1, option 0) press the “Up” button once. If you have the channel spacing (Menu 1) set to 6.25 KHz, the radio will set the channel correctly. 146520 or 444100, and three digits for the channel number, i.e. Note that the numbers speak when pressed. You can set the frequency by using the up/down buttons or by entering the frequency or channel number directly. You’ll know that the menu has exited if the radio beeps after a length of inactivity in the menu. Thus, if you’re changing several menu options in a row, it may not be necessary to press the menu key at the beginning of each operation. The radio will say “Confirm” to acknowledge a change in a menu’s parameters.Īlso be aware that the menu will stay active for a good 10 seconds after changing a menu option. Thus, after modifying a menu option, press the Menu key again to accept the change. When the Menu key is pressed, the radio will say “Menu”.
There is also a “roger beep” setting that you also want to disable.
It is not exactly clear what the differences are in these settings, but you want to turn them all off. There are three settings for eliminating repeater tail tones or courtesy tones. Having these on will make operating the radio annoying either to you or to the people you’re talking to. There are a couple of options that are turned on by default that it’s best to turn off. The info that follows will take you through the procedure. If you wanted to setup your transceiver via the units own keypad.
#CHIRP PROGRAMMING SOFTWARE FOR RADIOS PC#
You don’t have to use a PC to configure your transceiver, but it helps.
#CHIRP PROGRAMMING SOFTWARE FOR RADIOS DOWNLOAD#
I then had to download the programming software.
#CHIRP PROGRAMMING SOFTWARE FOR RADIOS DRIVERS#
It came complete with the USB drivers CD and the programming cable. I purchased my UV5R over the internet from a UK supplier. Here are a few notes to get you started on your UV5R, and I hope you find these useful. Getting Started with the UV-5R Baofeng UV-5R Want a pre-programmed Baofeng with UK repeater settings installed? Service available from Prepcomm UK You can buy a Baofeng from Amazon: Baofeng UV-5R – from Amazon
#CHIRP PROGRAMMING SOFTWARE FOR RADIOS HOW TO#
We’re very grateful to Steve M6UEH for putting together the following guide on how to get started with the popular Baofeng UV-5R handheld radio – hopefully, this will be of great help to first-time users of this powerful, low-priced amateur radio handheld
0 kommentar(er)
